Relevant Info -
CPU: AM2 5200
Mobo: M2N32-SLI Deluxe wifi edition
O/S: Vista 32 home premium
GPU: 2 X EVGA 7600GT 256mb (sli mode)
Monitor: Viewsonic 27" LCD T.V. utilizing DVI port from primary slot vga
(don't know model # off the top of my head, i'm at work, but I do know I dl
the unsigned drivers vista os zip file from viewsonic's website)
PSU: 600W
All drivers are current/up-to-date.

PROBLEM: Put computer into sleep mode either through start menu or pushing
pwr button (i've set requirement for pwr button < 4sec = sleep mode). I go
to work. 8 hrs later, I come back, click mouse or push a key on keyboard.
Electronically, computer wakes up, however, display/monitor stays on standby.
I'll press a button on the Viewsonic's remote control to get the bugger out
of standby mode, but it immediately goes back to a blank screen/standby,
which tells me, computer isn't "waking" up the lcd like it should OR
basically, the two ain't communicating.

So, I'll 1)Press the reset switch (but sometimes this is a hit or miss, b/c
upon reboot the LCD may or may not come out of standby and start displaying,
which again means the two ain't communicating), and if it does work, I'll get
asked to start in safe mode, last known config, etc. OR 2)I'll decide to
hold down pwr button, shut computer off, then power on, upon which I'll get
asked to start in safe mode, last known config, etc. This has been happening
before and after sli mode, so I know it's not that. This has been a pain in
the rear, even with XP, so I know it's not just another new bug with vista.
But now I'm finally fed up with it, and am querying about it.

Q: How do I fix?

I've tried messing with bios plug n play options, windows "sleep" mode
options, removing and re-plugging DVI cable while computer just sits there
on, the t.v.'s menu options, etc, but to no avail, the display won't come up.
So, I've just set settings to never turn off hard drive or monitor, or enter
sleep mode, and leave screensaver on, so that I don't have to deal with my
blank screen issue.

In advance, I'd like to thank all those that provide T/S tips, I'm
desperate. It'd be nice to come home, and after the comp has been asleep a
while, just click mouse button and everything comes up normally, everytime,
all the time. (This may also help you help me troubleshoot, USB Razer
diamondback mouse & USB generic dynex keyboard, AND this problem doesn't seem
to occur when the comp is in sleep mode for a short while, say less than 1 or
2hrs...)

Lastly, apologize for the novel read, I'm comp. literate and am capable of
entering the registry to tweak this or that, have exhausted the forums/faq
sections, and will do whatever I gotta do to get this unique problem solved
once and for all.

r/
Blank Screen

Maybe the unsigned drivers are the issue? Have you tried uninstalling the
Viewsonic & re-installing with Vista's built in signed drivers, to see what
happens?

JC

"calvnhobbes" wrote:
[color=blue]
> Relevant Info -
> CPU: AM2 5200
> Mobo: M2N32-SLI Deluxe wifi edition
> O/S: Vista 32 home premium
> GPU: 2 X EVGA 7600GT 256mb (sli mode)
> Monitor: Viewsonic 27" LCD T.V. utilizing DVI port from primary slot vga
> (don't know model # off the top of my head, i'm at work, but I do know I dl
> the unsigned drivers vista os zip file from viewsonic's website)
> PSU: 600W
> All drivers are current/up-to-date.
>
> PROBLEM: Put computer into sleep mode either through start menu or pushing
> pwr button (i've set requirement for pwr button < 4sec = sleep mode). I go
> to work. 8 hrs later, I come back, click mouse or push a key on keyboard.
> Electronically, computer wakes up, however, display/monitor stays on standby.
> I'll press a button on the Viewsonic's remote control to get the bugger out
> of standby mode, but it immediately goes back to a blank screen/standby,
> which tells me, computer isn't "waking" up the lcd like it should OR
> basically, the two ain't communicating.
>
> So, I'll 1)Press the reset switch (but sometimes this is a hit or miss, b/c
> upon reboot the LCD may or may not come out of standby and start displaying,
> which again means the two ain't communicating), and if it does work, I'll get
> asked to start in safe mode, last known config, etc. OR 2)I'll decide to
> hold down pwr button, shut computer off, then power on, upon which I'll get
> asked to start in safe mode, last known config, etc. This has been happening
> before and after sli mode, so I know it's not that. This has been a pain in
> the rear, even with XP, so I know it's not just another new bug with vista.
> But now I'm finally fed up with it, and am querying about it.
>
> Q: How do I fix?
>
> I've tried messing with bios plug n play options, windows "sleep" mode
> options, removing and re-plugging DVI cable while computer just sits there
> on, the t.v.'s menu options, etc, but to no avail, the display won't come up.
> So, I've just set settings to never turn off hard drive or monitor, or enter
> sleep mode, and leave screensaver on, so that I don't have to deal with my
> blank screen issue.
>
> In advance, I'd like to thank all those that provide T/S tips, I'm
> desperate. It'd be nice to come home, and after the comp has been asleep a
> while, just click mouse button and everything comes up normally, everytime,
> all the time. (This may also help you help me troubleshoot, USB Razer
> diamondback mouse & USB generic dynex keyboard, AND this problem doesn't seem
> to occur when the comp is in sleep mode for a short while, say less than 1 or
> 2hrs...)
>
> Lastly, apologize for the novel read, I'm comp. literate and am capable of
> entering the registry to tweak this or that, have exhausted the forums/faq
> sections, and will do whatever I gotta do to get this unique problem solved
> once and for all.
>
> r/
> Blank Screen
>
>
>[/color]

I get this issue also, but only on one model of CPU - the Dell OptiPlex 745's
using the digital LCD on Vista. I contacted Dell, they had two fixes (which
neither worked) 1st to flash the BIOS with their new update, no luck, and
then they said that this is a know issue with their 745 models, with a
Symantec conflict. preformed their suggested registry edit, also with no
luck. This is also a factory install of all driver, which are already the
newest that are listed on Dell's site as well as ATI which is providing the
vista drives for this model. So any help in this matter would be greatful

"calvnhobbes" wrote:
[color=blue]
> Relevant Info -
> CPU: AM2 5200
> Mobo: M2N32-SLI Deluxe wifi edition
> O/S: Vista 32 home premium
> GPU: 2 X EVGA 7600GT 256mb (sli mode)
> Monitor: Viewsonic 27" LCD T.V. utilizing DVI port from primary slot vga
> (don't know model # off the top of my head, i'm at work, but I do know I dl
> the unsigned drivers vista os zip file from viewsonic's website)
> PSU: 600W
> All drivers are current/up-to-date.
>
> PROBLEM: Put computer into sleep mode either through start menu or pushing
> pwr button (i've set requirement for pwr button < 4sec = sleep mode). I go
> to work. 8 hrs later, I come back, click mouse or push a key on keyboard.
> Electronically, computer wakes up, however, display/monitor stays on standby.
> I'll press a button on the Viewsonic's remote control to get the bugger out
> of standby mode, but it immediately goes back to a blank screen/standby,
> which tells me, computer isn't "waking" up the lcd like it should OR
> basically, the two ain't communicating.
>
> So, I'll 1)Press the reset switch (but sometimes this is a hit or miss, b/c
> upon reboot the LCD may or may not come out of standby and start displaying,
> which again means the two ain't communicating), and if it does work, I'll get
> asked to start in safe mode, last known config, etc. OR 2)I'll decide to
> hold down pwr button, shut computer off, then power on, upon which I'll get
> asked to start in safe mode, last known config, etc. This has been happening
> before and after sli mode, so I know it's not that. This has been a pain in
> the rear, even with XP, so I know it's not just another new bug with vista.
> But now I'm finally fed up with it, and am querying about it.
>
> Q: How do I fix?
>
> I've tried messing with bios plug n play options, windows "sleep" mode
> options, removing and re-plugging DVI cable while computer just sits there
> on, the t.v.'s menu options, etc, but to no avail, the display won't come up.
> So, I've just set settings to never turn off hard drive or monitor, or enter
> sleep mode, and leave screensaver on, so that I don't have to deal with my
> blank screen issue.
>
> In advance, I'd like to thank all those that provide T/S tips, I'm
> desperate. It'd be nice to come home, and after the comp has been asleep a
> while, just click mouse button and everything comes up normally, everytime,
> all the time. (This may also help you help me troubleshoot, USB Razer
> diamondback mouse & USB generic dynex keyboard, AND this problem doesn't seem
> to occur when the comp is in sleep mode for a short while, say less than 1 or
> 2hrs...)
>
> Lastly, apologize for the novel read, I'm comp. literate and am capable of
> entering the registry to tweak this or that, have exhausted the forums/faq
> sections, and will do whatever I gotta do to get this unique problem solved
> once and for all.
>
> r/
> Blank Screen
>
>
>[/color]

Since all the power to your MOBO is not turned off during a restart like it
is with a power off your problem may have something to do with the amount of
power available to your components and the sequence they come up in. It
appears that another device may be drawing too much power during restart at
the same time that you graphics card is trying to start.
I suggest that you set your floppy or a optical drive as your boot disk and
then let this device time out during boot with no disk installed this will
delay your boot HDD from drawing a lot of power right away.
"DeanFif" <DeanFif@discussions.microsoft.com> wrote in message
news:319ABEB6-99E9-4D54-924C-CD2E03FBDAB3@microsoft.com...[color=blue]
>I get this issue also, but only on one model of CPU - the Dell OptiPlex
>745's
> using the digital LCD on Vista. I contacted Dell, they had two fixes
> (which
> neither worked) 1st to flash the BIOS with their new update, no luck, and
> then they said that this is a know issue with their 745 models, with a
> Symantec conflict. preformed their suggested registry edit, also with no
> luck. This is also a factory install of all driver, which are already the
> newest that are listed on Dell's site as well as ATI which is providing
> the
> vista drives for this model. So any help in this matter would be greatful
>
> "calvnhobbes" wrote:
>[color=green]
>> Relevant Info -
>> CPU: AM2 5200
>> Mobo: M2N32-SLI Deluxe wifi edition
>> O/S: Vista 32 home premium
>> GPU: 2 X EVGA 7600GT 256mb (sli mode)
>> Monitor: Viewsonic 27" LCD T.V. utilizing DVI port from primary slot vga
>> (don't know model # off the top of my head, i'm at work, but I do know I
>> dl
>> the unsigned drivers vista os zip file from viewsonic's website)
>> PSU: 600W
>> All drivers are current/up-to-date.
>>
>> PROBLEM: Put computer into sleep mode either through start menu or
>> pushing
>> pwr button (i've set requirement for pwr button < 4sec = sleep mode). I
>> go
>> to work. 8 hrs later, I come back, click mouse or push a key on
>> keyboard.
>> Electronically, computer wakes up, however, display/monitor stays on
>> standby.
>> I'll press a button on the Viewsonic's remote control to get the bugger
>> out
>> of standby mode, but it immediately goes back to a blank screen/standby,
>> which tells me, computer isn't "waking" up the lcd like it should OR
>> basically, the two ain't communicating.
>>
>> So, I'll 1)Press the reset switch (but sometimes this is a hit or miss,
>> b/c
>> upon reboot the LCD may or may not come out of standby and start
>> displaying,
>> which again means the two ain't communicating), and if it does work, I'll
>> get
>> asked to start in safe mode, last known config, etc. OR 2)I'll decide to
>> hold down pwr button, shut computer off, then power on, upon which I'll
>> get
>> asked to start in safe mode, last known config, etc. This has been
>> happening
>> before and after sli mode, so I know it's not that. This has been a pain
>> in
>> the rear, even with XP, so I know it's not just another new bug with
>> vista.
>> But now I'm finally fed up with it, and am querying about it.
>>
>> Q: How do I fix?
>>
>> I've tried messing with bios plug n play options, windows "sleep" mode
>> options, removing and re-plugging DVI cable while computer just sits
>> there
>> on, the t.v.'s menu options, etc, but to no avail, the display won't come
>> up.
>> So, I've just set settings to never turn off hard drive or monitor, or
>> enter
>> sleep mode, and leave screensaver on, so that I don't have to deal with
>> my
>> blank screen issue.
>>
>> In advance, I'd like to thank all those that provide T/S tips, I'm
>> desperate. It'd be nice to come home, and after the comp has been asleep
>> a
>> while, just click mouse button and everything comes up normally,
>> everytime,
>> all the time. (This may also help you help me troubleshoot, USB Razer
>> diamondback mouse & USB generic dynex keyboard, AND this problem doesn't
>> seem
>> to occur when the comp is in sleep mode for a short while, say less than
>> 1 or
>> 2hrs...)
>>
>> Lastly, apologize for the novel read, I'm comp. literate and am capable
>> of
>> entering the registry to tweak this or that, have exhausted the
>> forums/faq
>> sections, and will do whatever I gotta do to get this unique problem
>> solved
>> once and for all.
>>
>> r/
>> Blank Screen
>>
>>
>>[/color][/color]

I've had this once, so far. I believe it to be hardware related because it
also failed to initialise the graphics card from cold a couple of times. I
took the side off the tower with the intention of pulling the graphics card
out and reseating it but, after getting the screw out of the bracket, failed
to get the retaining clip released from the back end of the card. Anyway,
wiggling it about, pushing it firmly into its slot and putting everything
back together seems to have helped; it hasn't happened since (so far).

I've also had the keyboard (PS2, not USB) go unresponsive coming out of
sleep mode. No idea what causes that yet.

Anyway, to sum up, make sure your graphics cards are fully seated in their
slots. Not sure how SLI works these days, but is there also a ribbon cable
between the two cards? If so, check that too.

One other important thing: make sure you and the computer are earthed before
touching anything inside.

Let us know how you get on.




"calvnhobbes" <calvnhobbes@discussions.microsoft.com> wrote in message
news:58CC3E99-D101-44BC-AA4C-5DFA6BE77223@microsoft.com...[color=blue]
> Relevant Info -
> CPU: AM2 5200
> Mobo: M2N32-SLI Deluxe wifi edition
> O/S: Vista 32 home premium
> GPU: 2 X EVGA 7600GT 256mb (sli mode)
> Monitor: Viewsonic 27" LCD T.V. utilizing DVI port from primary slot vga
> (don't know model # off the top of my head, i'm at work, but I do know I
> dl
> the unsigned drivers vista os zip file from viewsonic's website)
> PSU: 600W
> All drivers are current/up-to-date.
>
> PROBLEM: Put computer into sleep mode either through start menu or
> pushing
> pwr button (i've set requirement for pwr button < 4sec = sleep mode). I
> go
> to work. 8 hrs later, I come back, click mouse or push a key on keyboard.
> Electronically, computer wakes up, however, display/monitor stays on
> standby.
> I'll press a button on the Viewsonic's remote control to get the bugger
> out
> of standby mode, but it immediately goes back to a blank screen/standby,
> which tells me, computer isn't "waking" up the lcd like it should OR
> basically, the two ain't communicating.
>
> So, I'll 1)Press the reset switch (but sometimes this is a hit or miss,
> b/c
> upon reboot the LCD may or may not come out of standby and start
> displaying,
> which again means the two ain't communicating), and if it does work, I'll
> get
> asked to start in safe mode, last known config, etc. OR 2)I'll decide to
> hold down pwr button, shut computer off, then power on, upon which I'll
> get
> asked to start in safe mode, last known config, etc. This has been
> happening
> before and after sli mode, so I know it's not that. This has been a pain
> in
> the rear, even with XP, so I know it's not just another new bug with
> vista.
> But now I'm finally fed up with it, and am querying about it.
>
> Q: How do I fix?
>
> I've tried messing with bios plug n play options, windows "sleep" mode
> options, removing and re-plugging DVI cable while computer just sits there
> on, the t.v.'s menu options, etc, but to no avail, the display won't come
> up.
> So, I've just set settings to never turn off hard drive or monitor, or
> enter
> sleep mode, and leave screensaver on, so that I don't have to deal with my
> blank screen issue.
>
> In advance, I'd like to thank all those that provide T/S tips, I'm
> desperate. It'd be nice to come home, and after the comp has been asleep
> a
> while, just click mouse button and everything comes up normally,
> everytime,
> all the time. (This may also help you help me troubleshoot, USB Razer
> diamondback mouse & USB generic dynex keyboard, AND this problem doesn't
> seem
> to occur when the comp is in sleep mode for a short while, say less than 1
> or
> 2hrs...)
>
> Lastly, apologize for the novel read, I'm comp. literate and am capable of
> entering the registry to tweak this or that, have exhausted the forums/faq
> sections, and will do whatever I gotta do to get this unique problem
> solved
> once and for all.
>
> r/
> Blank Screen
>
>
>[/color]

Yes, this is a problem that occurs now and then, and Dell knows
about it as it appears on their consumer boards. My laptop uses
the Intel 945 driver, version 6.xx or 7.xx. You describe my
situation almost perfectly, and I know the screen illumination
is ON (can see slight bleed of light), but the LCD pixels are
all OFF. In other words, the problem is NOT the illumination
panel behind the LCD but the LCD itself.

Dell has had me reinstall versions of the video driver, to no
avail. Because the problem is intermittent, it might work three
or four times and appear to be "cured", then fail the next time.
Dell's next suggestion was to replace my mother board, but since
the situation changes with driver changes, I suspect software is
the problem.

I dislike this, but have been tolerating it knowing that new
video driver editions are forthcoming. And, somewhere/someone
has solved it - hopefully that information will be shared!

PLEASE post advice here, or send it to me at the address above
(remove the obvious).

Thanks!



Rojo Habe wrote:[color=blue]
> I've had this once, so far. I believe it to be hardware related because
> it also failed to initialise the graphics card from cold a couple of
> times. I took the side off the tower with the intention of pulling the
> graphics card out and reseating it but, after getting the screw out of
> the bracket, failed to get the retaining clip released from the back end
> of the card. Anyway, wiggling it about, pushing it firmly into its slot
> and putting everything back together seems to have helped; it hasn't
> happened since (so far).
>
> I've also had the keyboard (PS2, not USB) go unresponsive coming out of
> sleep mode. No idea what causes that yet.
>
> Anyway, to sum up, make sure your graphics cards are fully seated in
> their slots. Not sure how SLI works these days, but is there also a
> ribbon cable between the two cards? If so, check that too.
>
> One other important thing: make sure you and the computer are earthed
> before touching anything inside.
>
> Let us know how you get on.
>
>
>
>
> "calvnhobbes" <calvnhobbes@discussions.microsoft.com> wrote in message
> news:58CC3E99-D101-44BC-AA4C-5DFA6BE77223@microsoft.com...[color=green]
>> Relevant Info -
>> CPU: AM2 5200
>> Mobo: M2N32-SLI Deluxe wifi edition
>> O/S: Vista 32 home premium
>> GPU: 2 X EVGA 7600GT 256mb (sli mode)
>> Monitor: Viewsonic 27" LCD T.V. utilizing DVI port from primary slot vga
>> (don't know model # off the top of my head, i'm at work, but I do know
>> I dl
>> the unsigned drivers vista os zip file from viewsonic's website)
>> PSU: 600W
>> All drivers are current/up-to-date.
>>
>> PROBLEM: Put computer into sleep mode either through start menu or
>> pushing
>> pwr button (i've set requirement for pwr button < 4sec = sleep mode).
>> I go
>> to work. 8 hrs later, I come back, click mouse or push a key on
>> keyboard.
>> Electronically, computer wakes up, however, display/monitor stays on
>> standby.
>> I'll press a button on the Viewsonic's remote control to get the
>> bugger out
>> of standby mode, but it immediately goes back to a blank screen/standby,
>> which tells me, computer isn't "waking" up the lcd like it should OR
>> basically, the two ain't communicating.
>>
>> So, I'll 1)Press the reset switch (but sometimes this is a hit or
>> miss, b/c
>> upon reboot the LCD may or may not come out of standby and start
>> displaying,
>> which again means the two ain't communicating), and if it does work,
>> I'll get
>> asked to start in safe mode, last known config, etc. OR 2)I'll decide to
>> hold down pwr button, shut computer off, then power on, upon which
>> I'll get
>> asked to start in safe mode, last known config, etc. This has been
>> happening
>> before and after sli mode, so I know it's not that. This has been a
>> pain in
>> the rear, even with XP, so I know it's not just another new bug with
>> vista.
>> But now I'm finally fed up with it, and am querying about it.
>>
>> Q: How do I fix?
>>
>> I've tried messing with bios plug n play options, windows "sleep" mode
>> options, removing and re-plugging DVI cable while computer just sits
>> there
>> on, the t.v.'s menu options, etc, but to no avail, the display won't
>> come up.
>> So, I've just set settings to never turn off hard drive or monitor, or
>> enter
>> sleep mode, and leave screensaver on, so that I don't have to deal
>> with my
>> blank screen issue.
>>
>> In advance, I'd like to thank all those that provide T/S tips, I'm
>> desperate. It'd be nice to come home, and after the comp has been
>> asleep a
>> while, just click mouse button and everything comes up normally,
>> everytime,
>> all the time. (This may also help you help me troubleshoot, USB Razer
>> diamondback mouse & USB generic dynex keyboard, AND this problem
>> doesn't seem
>> to occur when the comp is in sleep mode for a short while, say less
>> than 1 or
>> 2hrs...)
>>
>> Lastly, apologize for the novel read, I'm comp. literate and am
>> capable of
>> entering the registry to tweak this or that, have exhausted the
>> forums/faq
>> sections, and will do whatever I gotta do to get this unique problem
>> solved
>> once and for all.
>>
>> r/
>> Blank Screen
>>
>>
>>[/color]
>[/color]

This sounds like a BIOS issue - have you checked Gateway's site for an
update?


"electroplater86" <guest@unknown-email.com> wrote in message
news:1c0f7a31fff9e00acb1a1b9da263a746@nntp-gateway.com...[color=blue]
>
> I'm having the same problem with an added twist. My computer won't come
> out of sleep mode right, no mouse or keyboard help there. But when I
> try a hard boot and then start the PC up again, it sounds like a typical
> startup, but still no response from the monitor AND the tower goes to
> sleep again. So I cannot get on my computer to make any changes!
>
> Oh yeah, running a Gateway LX6200 with Vista Home Premium 64bit.
>
>
> --
> electroplater86[/color]

This sounds like a BIOS issue - have you checked Gateway's site for an
update?


"electroplater86" <guest@unknown-email.com> wrote in message
news:1c0f7a31fff9e00acb1a1b9da263a746@nntp-gateway.com...[color=blue]
>
> I'm having the same problem with an added twist. My computer won't come
> out of sleep mode right, no mouse or keyboard help there. But when I
> try a hard boot and then start the PC up again, it sounds like a typical
> startup, but still no response from the monitor AND the tower goes to
> sleep again. So I cannot get on my computer to make any changes!
>
> Oh yeah, running a Gateway LX6200 with Vista Home Premium 64bit.
>
>
> --
> electroplater86[/color]

Go to Advance Power Settings.
Set hard drive to turn off a minute or 2 before sleep.
Set Hybrid and Hibernate modes to "Never/Off"
Under USB settings select "Disable"
Under Multimedia select "Allow ....."


How to Troubleshoot a Vista Sleep Mode Problem and Find a Solution
[url]http://www.vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html[/url]


"kompak" <guest@unknown-email.com> wrote in message
news:6e7e41548725f085b0402c7ea8d32340@nntp-gateway.com...[color=blue]
>
> Hi, I have compaq SR5510f 4GB RAM, Athlon X2 5000+ with same issue,no
> display after resuming from sleep mode + the processor fan keeps on
> running on high speed all the time and the pc cannot be put in sleep
> mode again, just restart via tower button. I have 512Mb ATI HD 4550
> Saphire Radeon and Samsung T220HD LCD HDTV/Monitor. Power supply
> upgraded to Thermaltake 430W. All components working OK as per Device
> Manager. Contacted HP support, tried all this:
> 1. Updated BIOS with versions 5.27 which claims that this problem is
> solved; checked PCI-E as a primary video adapter in Bios
> 2. Updated all drivers (+ installed fresh copy of windows)
> 3."Allow this device to wake the computer" checked in Control Panel for
> Mouse/Keyboard
> 4.Cleaned PC from dust
> 5. Reinstalled (physically and software) Graphic Card
> NOTHING worked. Finally, HP suggest to take the PC to service as there
> is probably hardware issue.
> I beleive it is BIOS )BIOS is the one that prepares the machine after
> identifying,testing and initializing PC devices) or hardware issue. As
> my PC is just out of warranty, thinking of buying different motherboard
> to solve this. Current motherboard is ECS MCP61PM-HM REV. 1.0B
> Anyone has any other idea how to solve this issue???
>
>
> --
> kompak[/color]